What Not to Do When Insulating Plastic Windows in Minsk

With the onset of the cold, many residents of Minsk and Minsk district begin to look for ways to warm up plastic windows. There are many methods in the works: scotch, boron, self-adhesive sealants, drainage holes. Unfortunately, most of these methods are not only useless, but can also lead to serious breakdowns, which will cost much more than professional solution of the problem.

I, Dmitry, a window repair expert with 20 years of experience, face the consequences of this kind of 'warming' every year. In this article, I will tell you what you absolutely cannot do with plastic windows to avoid damaging them, and how to prepare windows properly for winter.

The most common mistakes in window warming

1. Window slats with scotch (except for paint tape)

The paint tape is a relatively safe option if it is high quality and easy to remove. But the usual clear or brown scotch leaves sticky traces that are very difficult to erase. Using acetone or other solvents to remove glue can damage plastic and rubber sealants.The Council:If you're gluing, use only high-quality paint tape and remove it immediately after winter, without waiting for the glue to fade.

2. Inserting a poron or additional sealants inside the frame

Many people try to seal the gaps with a perforation or to paste the second row of the sealant.

• create excessive pressure on the fittings, causing the handle to rotate with difficulty, and the mechanisms to wear out faster;
• may deform the original sealant, after which it ceases to perform its functions;
• They leave traces of glue that are hard to remove.

If the window is bloating, it's not because of a lack of a perforation, but because of a geometry violation, seal wear, or installation errors.

3. Drainage holes are closed

Drainage holes at the bottom of the frame are designed to drain water that can get inside in the event of rain or snow melt.

• to get the ponds on the window and floor when the water cannot go out;
• provoke freezing and formation of ice within the profile;
• create conditions for mold and fungus.

From a warming perspective, drainage glue is useless; the passageway doesn't come from these holes.

4. Glue seals on the original rubber

Sometimes people stick self-adhesive tape directly to or parallel to the existing sealant, which results in the same effects: overloading the fitting, deformation of the rubber, problems with closing. Instead of warming up, you get accelerated wear and tear of the parts and the potential for breaking the locks.

How to prepare plastic windows for winter

You don't have to invent a bicycle to keep windows cool, just take a few simple steps and ask a specialist to diagnose the condition.

1. Check the condition of the sealant.If the rubber has lost its elasticity, cracked or splintered, it needs to be replaced with a high-quality one (German brands REHAU, KBE, Schlegel).
2. You can evaluate the geometry of the beams.The work must not be suspended or attached to the frame.
3. Set the pressure (snaps).If the window is in good condition, it is enough to leave the position neutral.
4. Fresh the furniture.Clean and lubricated appliances work easier and last longer.
5. Check the seams.If it blows from under the window or the windows, it will require a re-heat.

It's hard to determine the cause of the bloating on your own, and I recommend that you invite a professional to check it out at least once a year, which is cheaper than fixing a broken piece of furniture or changing the shutter.

Frequently Asked Questions

Can I use scotch if it's very cold?

Just a quality scotch, as a temporary measure, remember that it doesn't eliminate the cause of the scratch, it just masks it.

Why did the window have such a hard time closing after the additional sealant was glued?

Because you've created an excess pressure, the furniture isn't designed for this load, so take off the sealant and ask the master to adjust it.

What if the drainage is blowing?

It's normal to have a profile ventilation through them. If the drain is strong, it might be a problem with the strong pull in the house. But you can't glue the holes.

How much does a professional window warmer cost?

The cost depends on the amount of work. The excursion and the diagnosis are free. I call it the cost after the inspection.

Why should I trust the windows to warm up?

• 20 years of experience.I know all the details of the window frames and I'll find the cause of the bloating quickly.
• Free admission and diagnosis.I'll come to Minsk or Minsk district, check the windows and suggest the best solution.
• Honesty is what it is.I'm not going to force any extra work.
• The materials are of high quality.I only use certified sealants and fittings.
• Guarantee up to one year.I give a written guarantee on all types of work.

Order professional window preparation for winter in Minsk

Do not experiment with scotch and broth — it can cost you expensive repairs. Call me right now for free consultation and registration at a convenient time. I work in Minsk and Minsk district quickly and with quality guarantee.

Telephone for communication: +375 (29) 135 -50-50